Short answer: Ground improvement materials are mostly grouped by chemical base: clay-based such as bentonite, carbon-based, polymer-based (gels and liquids), metal-based, and salts and chemicals. The main difference lies in how they carry current: carbon and metal materials are conductive in themselves, while clay, gel and salt only conduct when they hold water. For a permanent earthing system the type of material alone is not enough: it must also have passed the IEC 62561-7 tests.
In this article we at KALOT Group explain each type simply and show where it is useful. How these materials evolved over time from salt and charcoal to standardised products is covered in What kinds of substances are ground improvement materials?
What exactly does a ground improvement material do?
An earth electrode (an earth rod, plate or tape) passes current into the soil. Most of the resistance sits in the soil right next to the electrode, because the current has only a small area to pass through there. For example, with a 3 m earth rod about one-fifth of the resistance lies in the first 3 cm around the rod and about 40% in the first 10 cm (calculated with the earth rod resistance formula for uniform soil). A ground improvement material fills exactly this zone with something more conductive than the soil, as if the electrode had a larger diameter and fuller contact with the soil.
The material does not replace the soil further away. So in very high-resistivity soil it lowers the resistance but works no miracles, and sometimes longer or additional electrodes are also needed. We work out the size of the effect with a numerical example in Why is ground improvement material useful for earthing?
Electronic and ionic conduction: the key to understanding the types
- Electronic conduction: carbon or metal particles touch one another and current flows through the material itself, as in a wire. This conduction does not depend on water, so it holds up in the dry season too.
- Ionic conduction: current is carried by ions dissolved in water, as in moist clay, a water-holding gel or a salt solution. It works as long as water is present, but when the soil dries out the resistance rises. Salts also dissolve in water and gradually wash away.
This is why soil moisture affects each type of material differently (Is soil moisture a key factor in how ground improvement materials lower resistance?).
Types of ground improvement material by chemical base
1. Mineral soil or clay-based materials
The best-known example of this group is bentonite, a clay made of the mineral montmorillonite that swells to several times its dry volume in water and holds moisture. BS 7430:2026 considers bentonite suitable for soils whose moisture varies with the seasons, provided it is fully hydrated during installation. Its weakness comes from the same place: bentonite conducts ionically, so its resistance climbs quickly when moisture is short, and as it dries it shrinks and pulls away from the electrode. Some commercial bentonites also contain salt (Is bentonite a standard material?).
2. Carbon-based materials
These materials are made of conductive carbon or graphite particles. They are usually mixed with cement and water and poured as a slurry around the electrode, hardening into a solid column bonded to it. Another example is conductive concrete, which uses conductive carbon granules in place of sand and aggregate. They conduct electronically and do not dissolve or wash out in water. BS 7430:2026 accepts slurries containing graphite or carbon powder for backfilling around earth rods and earth tapes, and also suggests conductive concrete for rocky, high-resistivity terrain, provided the material does not shrink after drying or separate from the electrode.
One important point: not every black, carbon-rich material meets the standard. Petroleum coke and power-plant fly ash also contain carbon, but their sulphur and corrosive substances attack the electrode, which is why IEC 62561-7 requires less than 2% sulphur in the material. The full explanation of this group is in Carbon-based ground improvement materials. The GIM ground improvement material we manufacture belongs to this group.
3. Polymer-based materials: ground improvement gels and liquids
In this group, water-absorbing polymers (such as hydrogels) or gels containing an electrolyte are placed around the electrode. The polymer holds water like a sponge and its electrolyte provides ionic conduction. What the market calls a "ground improvement liquid" or "earthing gel" usually belongs to this family or is a salt solution. Their advantages are simple installation and penetration into coarse-grained and stony soil. But because their conduction depends on water and ions, their durability depends on the product's composition, so before buying, ask for the leaching and corrosion test report to IEC 62561-7. Research on this group is still ongoing, and there is less long-term field data for it than for carbon materials.
4. Metal-based materials
In this group, powders or granules of conductive metals and metal oxides, or solutions and gels based on copper compounds, are poured around the electrode. Metal granules conduct electronically, but two points need attention: a metal different from the electrode material can form a galvanic couple in moist soil and speed up corrosion, and soluble metal compounds such as copper sulphate are in practice a form of chemical treatment and wash out. The IEC 62561-7 leaching test measures precisely such metals as copper, zinc, lead and chromium in the outflow water (Ground improvement materials and earthing system corrosion).
5. Salts and chemicals
Table salt, calcium chloride, magnesium sulphate and copper sulphate are the oldest ways of lowering resistance. According to IEEE Std 142, these substances reduce soil resistivity by 15 to 90% depending on the soil type, but the effect does not last, they must be renewed periodically and they harm the electrode's protection against corrosion. BS 7430:2026 also does not regard chemical soil treatment as a long-term solution, because of its environmental impact and corrosion risk, and it prohibits the use of coke because it is highly corrosive. The old salt and charcoal pits belong to this group (Are salt and charcoal a standard ground improvement material?).
Types of ground improvement material by supply form
- Dry powder: poured around the electrode and activated by water or soil moisture, such as powdered bentonite.
- Slurry and cement mix: the powder is mixed with water (and sometimes cement), poured into a borehole or trench and left to harden, as with carbon-based materials and conductive concrete. The standard tests are carried out on this final mix, not on the powder in the bag.
- Granules: conductive or moisture-absorbing granules that are poured in and compacted like backfill soil.
- Gel and liquid: poured onto or injected into the soil around the electrode, where they penetrate the ground; usually polymer-based or salt-based.
- Chemical (electrolytic) earth rod: a hollow copper tube filled with electrolyte salts that absorbs moisture and gradually releases a salt solution into the surrounding soil. Makers install these earth rods with a conductive backfill and an inspection pit. Because the salt runs out over time, ask the seller whether it can be recharged or replaced.
Summary table of ground improvement material types
Material type | Example | Conduction type | Moisture dependence | Durability |
|---|---|---|---|---|
Clay-based | Bentonite | Ionic | High; shrinks when dry | Medium; better in moist soil |
Carbon-based | Carbon slurry, conductive concrete | Electronic | Low | Stable; does not wash out |
Polymer-based | Hydrogel, ground improvement gel and liquid | Ionic | High | Depends on composition; ask for a test report |
Metal-based | Metal granules and oxides, copper compounds | Electronic or ionic | Depends on composition | Depends on composition; risk of galvanic corrosion |
Salts and chemicals | Table salt, sulphates, calcium chloride | Ionic | High | Low; washes out and must be renewed |
A fuller comparison with the pros, cons and uses of each material is in our comparison table of ground improvement material types.
The type is not enough: which ground improvement material meets the standard?
Two materials in the same group can behave quite differently. That is why IEC 62561-7, rather than naming a type of material, makes a set of tests mandatory: leaching (the material must not release heavy metals and harmful substances into soil and water), sulphur below 2%, resistivity measurement with the value marked on the pack, pH, and a corrosion test on the electrode. In Iran, too, Article 63 of the Earthing System Safety Code (1401) requires earth pit additives to be tested according to national standard INSO 18499-7. We give the details in The standard for ground improvement materials and Specifications of standard ground improvement materials, and the environmental effect of these materials is examined in Are ground improvement materials pollutants?
Which type of ground improvement material should you choose?
- Permanent earthing system, dry, rocky or high-resistivity soil: a tested carbon-based material that does not wash out and does not rely on moisture.
- Moist soil and high-rainfall area, small project: bentonite can also work, provided it is properly hydrated during installation and contains no salt.
- Coarse-grained or stony soil that will not hold a slurry: consider gels and polymer materials only with a complete test report.
- Temporary, urgent need: salt, but only with a regular maintenance plan; not for a permanent system.
You do not always need a ground improvement material: in low-resistivity soil, the right electrode is enough (Must ground improvement materials always be used, in every soil?). A selection guide by soil type is in Which materials should be used in which soils?
We manufacture the GIM family of ground improvement materials to IEC 62561-7: GIM for highly corrosive soils and environments, GIM LIGHT for normal conditions, and ECO GIM. Install the material together with a copper-bonded earth rod, exothermic welding (KALweld®) connections and an inspection pit, so periodic measurement stays simple. Estimate the quantity with the GIM calculator, or send our specialists the soil type, the result of your soil resistivity measurement and the target resistance. We also carry out earthing system design and earthing system measurement and testing; reach us through our contact page.



