Move your pointer over the image to zoom in
Complete Product Overview
Polyethylene earth pit (earth inspection pit)
Last updated:
The KALOT Group polyethylene earth pit (code PE 3030) is installed over the top of an earth rod or earth pit and keeps the joint between the earth electrode and the conductors within reach for inspection, testing and resistance measurement, with no digging. The body and cover are black polyethylene, made from virgin polymer resin with no recycled material and a UV-resistant additive. The reinforced 250 × 250 cover, with the KALOT mark and earth symbol, sits level with the ground and is fastened with two recessed Allen bolts. The standard bar is 304 stainless steel, 238 × 30 × 5 with four 10 mm holes. It stands upright on the diagonal in two slots on the pit's inner rim and connects the earth rod conductor to the building conductor, the lightning protection down conductor or the next pit. We also make bare or tinned copper bars to order. The pit is made to IEC 62561-5. Three samples were load tested at the Razi Metallurgical Research Centre to IEC 62561-5:2023, and the pit passed in heavy class (H) at a load of 30 kN. The polyethylene earth pit is one of KALOT Group's best-selling products and is also exported to markets abroad. We can also recommend the right bar, clamps and cable lugs.
The floor of this earth chamber is open and slotted so the earth rod can pass through, and its 300 × 300 base flange, with the concrete that is always poured around the pit, holds it firmly in place. The pit's 238 × 30 × 5 earth bar, with four 10 mm holes at 40 mm spacing, is made as standard from 304 stainless steel, and we also make bare or tinned copper versions to order. The number, diameter and spacing of the holes can change to suit the order and the project. The earth bar and its stainless steel bolts, nuts and washers are supplied separately. To see a three-dimensional view of how this pit is installed and executed, click here. You will find the table "Concrete or polyethylene earth pit: a comparison" under the "Why an earth pit?" tab on this page or on the concrete earth pit page.
Earth pit inspection point, level with the ground
The pit sits over the earth rod and keeps the joint between the electrode and the conductors always within reach. To inspect or measure, you simply open the cover.
- Heavy load class (H), 30 kN; IEC 62561-5:2023 test on three samples
- Open floor for the earth rod to pass through
- 304 stainless steel bar with four holes, set diagonally in two slots on the inner rim
- Lightweight polyethylene (1.8 kg) from virgin resin with a UV-resistant additive
Bar seating
Two slots on the inner rim hold the 238 × 30 × 5 bar upright on the diagonal, so conductors can be fixed with cable lugs on its four 10 mm holes. The standard bar is 304 stainless steel and is supplied separately.
Open floor and wide flange
The earth rod passes through the slotted floor, and the 300 × 300 base flange holds the pit firmly in the surrounding concrete.
Heavy load class (H), 30 kN
Load test report (PDF)Website membership required · Sign in or joinThree samples of this pit were load tested at the Razi Metallurgical Research Centre to IEC 62561-5:2023 (clauses 4.1 and 6.4), and the pit passed in heavy class (H) at a load of 30 kN (about 3 tonnes). The seating and the concrete around the pit must suit the installation location. For vehicle routes, please agree the location with our specialists.
Drawings and datasheet
Polyethylene earth pit datasheet (PDF)You have the dimensional drawing, technical drawing, exploded view, execution schematic, installation steps and earth rod connection methods as PDF files alongside the datasheet, and a three-dimensional view on this page.
Advice from KALOT Group specialists
Along with the pit, our specialists recommend the right clamps, bar and cable lugs for your installation location and conductor types.
Technical Product Information
Click to view enlarged
Feature | Value |
|---|---|
Type | Earth electrode inspection pit (earth inspection chamber) |
Code | PE 3030 |
Body and cover material | Black polyethylene from virgin polymer resin, no recycled material, with a UV-resistant additive |
Pit dimensions | 300 × 300 × 205 mm |
Cover | Reinforced 250 × 250 mm cover with the KALOT mark and earth symbol, fastened with two recessed stainless steel Allen bolts in opposite corners |
Base flange | 300 × 300 mm, rounded corners, with reinforcing ribs |
Body | Cylindrical, 190 mm diameter and about 150 mm long |
Total height | 205 mm |
Weight | 1.8 kg |
Standard | To IEC 62561-5 |
Tested load rating | Heavy class (H), 30 kN; load test on three samples at the Razi Metallurgical Research Centre to IEC 62561-5:2023 (clauses 4.1 and 6.4), with no cracking |
Bar seating | Diagonal, in two slots on the inner rim; the bar stands upright |
Bar (supplied separately) | 304 stainless steel (standard); bare or tinned copper to order |
Bar dimensions | 238 × 30 × 5 mm |
Bar holes | 4 Ø10 holes at 40 mm spacing (standard); the number, diameter and spacing of holes can change to suit the order and the project |
Bar bolts and nuts | Stainless steel bolts, nuts and washers; supplied separately |
Base | Slotted, for the earth rod to pass through |
Installation location | Over the top of an earth rod or earth pit, level with the finished ground |
Sizes
Model | Base flange A (mm) | Top and cover B (mm) | Body diameter D (mm) | Overall height H (mm) |
|---|---|---|---|---|
PE 3030 | 300 × 300 | 250 × 250 | 190 | 205 |
Dimensions are in millimetres. The cylindrical body extends about 150 mm below the base flange, and after installation the top of the cover is level with the finished ground. We keep improving our products and some dimensions may be updated, so please confirm the final dimensions with our specialists before you buy.
Dimensional drawing
Download the dimensional drawing (PDF)
Technical drawing
Download the technical drawing (PDF)
Exploded view
Download the exploded view (PDF)
Pit construction
The pit has two parts: a one-piece body and a cover. The body consists of a wide base flange with reinforcing ribs, which holds the pit in the surrounding concrete, and the cylinder below it, which sits over the earth rod. The reinforced square cover is fastened to the body with two recessed Allen bolts in opposite corners. The floor of the cylinder is slotted so the earth rod can pass through, and two slots on the inner rim hold the bar upright on the diagonal, so conductors can be fixed to it with cable lugs.
Click to view enlarged
Applications of the polyethylene earth pit
- Building earth pits and earth rods: an inspection and resistance measurement point for the earth electrode, over an earth rod or earth pit.
- Lightning protection systems: at the foot of every air terminal down conductor, where it joins the earth electrode.
- Earth rings and multiple electrodes: where electrodes connect to each other and to the building's earth bar, with conductors leaving from the bar inside the pit.
- Green spaces, pavements and open areas: where a light pit level with the ground is needed. For vehicle routes, please agree the location with our specialists.
Installation schematic
Download the execution schematic (PDF)
Earth rod connection inside the pit
Download connection modes (PDF)
Polyethylene earth pit installation steps
- Dig a hole about 600 × 600 and about 350 mm deep, and drive the earth rod until you reach the design resistance.
- Lay a sand bed under and around the earth rod so that water can drain.
- Set the pit over the earth rod so the rod passes through the slotted floor and the top of the cover is level with the finished ground.
- Connect the earth rod to the conductor with a U clamp, G clamp, A clamp or exothermic weld.
- Stand the bar on the diagonal in the two slots on the inner rim, then fix the earth rod conductor, down conductor, building conductor and next-pit conductor, each with a cable lug on one hole, using stainless steel bolts, nuts and washers. Put the earth rod conductor on an end hole so it is easy to undo for testing. Tighten the bolts according to the manufacturer's instructions.
- Always pour concrete around the pit so it stays in place and does not tilt over time. Make the seating and the surrounding concrete suit the load at the installation location, and for vehicle routes please agree the location with our specialists. Then backfill and level the surrounding area.
- Undo the earth rod conductor's cable lug from the bar so the earth rod is isolated from the rest of the system, measure its resistance and record it. Then refit the cable lug to the bar and fasten the cover with the two recessed Allen bolts.
Download the installation steps (PDF)
Installation tools
For installation you need a spade and digging tools, a hammer or earth rod driving machine, concrete for around the pit, a spanner for the clamps and cable lugs, an Allen key for the cover bolts and an earth resistance tester.
Inspection and measurement
During periodic inspections, open the pit, check the condition of the clamps and cable lugs, undo the earth rod conductor's cable lug, measure and record the earth rod's resistance and reconnect the joint. See our article on measuring earth resistance for more.
Selection and price enquiry
To get a price for the polyethylene earth pit, send our specialists the quantity, the installation location (green space, pavement or vehicle route), the earth rod diameter, the conductor types and the material and number of holes of the bar.
Click to view enlarged
The joint between the earth electrode and the conductors is the most important point in an earthing system, and over time it must be seen and tested. If this point stays under the soil, every inspection or measurement means digging. An earth pit keeps it level with the ground and within reach: you open the cover, see the joints, undo the earth rod conductor's cable lug and measure the earth rod's resistance.
Advantages of the polyethylene earth pit
- Heavy load class (H): three samples of this pit passed the IEC 62561-5:2023 load test at the Razi Metallurgical Research Centre in heavy class (H) at a load of 30 kN.
- Inspection with no digging: the earth rod and conductor joints are always within reach.
- Light and easy to install: at 1.8 kg it is far lighter than a concrete pit of the same size, easy to move and place over the earth rod, and the edges of its polymer body do not chip in handling.
- Virgin resin, no rust, stable in sunlight: the body and cover are made from virgin polymer resin with no recycled material, so material quality stays consistent. Polyethylene does not rust in damp soil, and a UV-resistant additive keeps it stable in sunlight.
- 304 stainless steel bar: several conductors join on one bar with cable lugs. The standard bar is 304 stainless steel with four holes, and we also make bare or tinned copper bars and other hole layouts to order.
- Reinforced cover with two recessed Allen bolts: the reinforced cover is fastened with two recessed Allen bolts in opposite corners, and the KALOT mark and earth symbol on it show where the earth electrode is.
Concrete or polyethylene earth pit: a comparison
Feature | Concrete earth pit | Polyethylene earth pit |
|---|---|---|
Body and cover material | Precast reinforced concrete | Black polyethylene from virgin resin, no recycled material, with a UV-resistant additive |
Dimensions (mm) | 310 × 310 × 170 | 300 × 300 × 205 (lid 250 × 250) |
Body shape | Square frame with sloping walls and a slot at the bottom of two opposite walls | Wide base flange with reinforcing ribs and a 190 diameter cylindrical body |
Base | Open; the earth rod enters the pit from the floor | Slotted; the earth rod passes through the centre of the floor |
Cover | Concrete slab with a lifting slot | Reinforced cover with the KALOT mark and earth symbol, with two recessed Allen bolts |
Bar seating | Upright in slots across the pit's diameter | Diagonal, in two slots on the inner rim |
Bar (separate) | 300 × 50 × 5 (both ends bevelled), 4 Ø12 holes; bare copper, tinned copper or stainless steel | 238 × 30 × 5, 4 Ø10 holes; 304 stainless steel (standard), bare or tinned copper to order |
Load rating in IEC 62561-5 testing | Medium (M), 15 kN; 2017 edition | Heavy (H), 30 kN; 2023 edition, three samples |
Weight and handling | 21.2 kg | 1.8 kg; easy to handle |
Installation | Level with the ground, always with concrete around the pit | Level with the ground, always with concrete around the pit |
For details of the concrete pit, see the concrete earth pit and the concrete earth pit bar.
If this matches your situation, see these products too
Product | When |
|---|---|
For the earth electrode under the pit. | |
U clamp for connecting conductor to earth rod and reinforcing bar | For clamping bare copper conductor to the earth rod. |
For connecting copper conductor to the earth rod. | |
For connecting copper tape to the earth rod. | |
For a permanent joint between conductor and earth rod. | |
When you need a concrete pit with a 300 × 50 × 5 bar. | |
When earth resistance needs to come down. |
We design and manufacture the polyethylene earth pit to IEC 62561-5, the standard that sets requirements for earth electrode inspection housings, including enough room to fasten and undo the connection and a mechanical load classification. It defines three load classes: light (L) at 4 kN for pavements, medium (M) at 15 kN for slow passenger car traffic and heavy (H) at 30 kN for slow multi-axle vehicle traffic. Three samples of this pit were load tested at the Razi Metallurgical Research Centre to IEC 62561-5:2023 (clauses 4.1 and 6.4), and the pit passed in heavy class (H). The seating and the structure around the pit must also suit the installation location.
IEC 62305-3 requires periodic inspection and testing of the earthing system of a lightning protection installation, and an earth pit keeps the place for this inspection and measurement within reach.
Part Thirteen of the Iranian National Building Regulations requires earth electrode resistance to be measured after installation and periodically thereafter.
The earthing system designer decides the pit locations, electrode type and connection method. To learn more, see earthing system design and installation standards.
Three-dimensional view of polyethylene earth pit installation
Documents & Downloads
Catalogues & datasheets
Drawings & schematics
- Polyethylene earth pit dimensional drawingLanguage: Persian (opens in a new tab)
- Polyethylene earth pit technical drawingLanguage: Persian (opens in a new tab)
- Polyethylene earth pit exploded viewLanguage: Persian (opens in a new tab)
- Polyethylene earth pit installation schematicLanguage: Persian (opens in a new tab)
- Polyethylene earth pit connection modesLanguage: Persian (opens in a new tab)
- Polyethylene earth pit installation stepsLanguage: Persian (opens in a new tab)
Certificates & test reports
- Load test report for polyethylene earth inspection pit to IEC 62561-5 (2023) | 2026Persian · 2026-08-24
Similar & Complementary Products
Frequently Asked Questions
What is a polyethylene earth pit and what is it used for?
It is a small polyethylene chamber installed over the top of an earth rod or earth pit, level with the ground. It keeps the joint between the earth electrode and the conductors within reach for inspection and resistance measurement, with no digging.
What are the pit's dimensions and weight, and how deep does it go into the soil?
The code for this pit is PE 3030 and it measures 300 × 300 × 205 mm: cover 250 × 250, base flange 300 × 300 and body diameter 190 mm, with a weight of 1.8 kg. It is installed so that the top of the cover is level with the finished ground and the body sits down to a depth of 205 mm below it.
Why is the floor of the pit open, and how does the earth rod pass through it?
The floor of the body is slotted so you can set the pit over an earth rod that has already been driven, with the rod passing through the centre of the floor. The top of the earth rod and its clamp stay inside the pit and within reach.
How does the bar sit inside the pit, and how many conductors connect to it?
The 238 × 30 × 5 earth bar is supplied separately and stands upright on the diagonal, in two slots on the pit's inner rim. The standard earth bar is 304 stainless steel with four 10 mm holes at 40 mm spacing. We also make bare or tinned copper earth bars to order, and the number, diameter and spacing of the holes can change to suit the order and the project. Each hole takes one conductor with a cable lug, for example the earth rod conductor, the lightning protection down conductor, the building conductor and the conductor to the next pit. The earth rod conductor goes on an end hole so it is easy to undo for testing. We also supply matching stainless steel bolts, nuts and washers separately.
How is the cover fastened?
The reinforced square cover is fixed to the body with two recessed stainless steel Allen bolts in opposite corners. The bolt heads sit inside the cover, and the KALOT mark and earth symbol on the cover show where the earth electrode is.
What load can a polyethylene earth pit carry?
Three samples of this pit were load tested at the Razi Metallurgical Research Centre to IEC 62561-5:2023, and the pit passed in heavy class (H) at a load of 30 kN (about 3 tonnes). The standard defines light class (L) at 4 kN for pavements, medium class (M) at 15 kN for slow passenger car traffic and heavy class (H) at 30 kN for slow multi-axle vehicle traffic. The seating and the structure around the pit must suit the installation location. Always pour concrete around the pit, and for vehicle routes please agree the location with our specialists.
Which is better, a polyethylene or a concrete earth pit?
At 1.8 kg the polyethylene pit is far lighter and easier to move and place. It is made from virgin polymer resin, its edges do not chip in handling, its open floor sits over the earth rod and its tested load class is heavy (H). The concrete earth pit weighs 21.2 kg, has a medium (M) load rating of 15 kN and takes a 300 × 50 × 5 bar. The choice depends on the installation location and the method of execution.
Why must concrete be poured around the pit?
Concrete around the pit holds it in place, so over time it does not tilt or shift with soil settlement or passing loads, and the cover always stays level with the ground.
How do we measure earth pit resistance from inside the pit?
Open the cover and undo the earth rod conductor's cable lug from the bar, so the earth rod is isolated from the rest of the system. Measure its resistance with an earth resistance tester, record the result and reconnect the joint.
What information should we send for a quote?
Send us the number of pits, the installation location, the earth rod diameter, the conductor types and the material and number of holes of the bar, and our specialists will propose the clamps, bars and cable lugs and give you a price.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.


