Move your pointer over the image to zoom in
Complete Product Overview
Three-piece U clamp for connecting two conductors to earth rod and reinforcing bar
Last updated:
The KALOT Group three-piece U clamp connects two copper earth conductors to one earth rod or reinforcing bar at the same time. The U bolt loops around the earth rod or reinforcing bar and three brass plates slide onto its legs, with each conductor sitting in its own tier between two plates. Tightening the two nuts compresses both conductors and seats the earth rod firmly in the top plate. The result is a bolted connection you can open for inspection and measurement, then close again.
We made this clamp for places where two conductors must reach one earth rod: for example, a down conductor and an earth ring conductor inside an earth inspection pit, or two bonding conductors on one reinforcing bar, whether inside the foundation reinforcement cage before the pour or at a connection point that stays accessible. Each conductor, independently of the other, is fastened in line with the earth rod or at right angles to it, and can pass through the clamp or terminate in it. The body is brass, and the U bolt and nuts are stainless steel. The clamp with code UBTV 1416 takes an earth rod or reinforcing bar of 14 to 20 mm and copper conductors of 16 to 150 mm² each. For one conductor, see our two-piece U clamp in six codes.
Two conductors, one clamp: connecting to an earth rod or reinforcing bar in one go
To choose this clamp, check two sizes: the diameter of the earth rod or reinforcing bar (14 to 20 mm) and the cross-section of each conductor (16 to 150 mm²).
- Two copper conductors to one earth rod or reinforcing bar
- Three brass plates, each conductor in its own tier
- Each conductor in line or at right angles, through-run or terminating
- Stainless steel U bolt and nuts
Three plates, two conductor tiers
The top plate rests on the earth rod through its seat. The first conductor goes between the top and middle plates, the second between the middle and outer plates. Each tier has a central hole for a conductor in line with the earth rod and a transverse hole for a conductor at right angles to it, so you can fasten the two conductors in any combination of these directions.
Where two conductors meet one earth rod
Instead of two separate clamps on one earth rod, a single three-piece clamp fastens a down conductor and an earth ring conductor, or two bonding conductors, to the earth rod or reinforcing bar. Undoing the two nuts frees both conductors for inspection and measurement.
Material: brass and stainless steel
The three-plate body is cast brass, and the U bolt and nuts are stainless steel. The KALOT mark and the sizes "16-150" and "Ø14-20" are cast on the outer plate.
Code UBTV 1416 and drawings
Three-piece U clamp datasheet (PDF)You will find the dimensional drawing, technical drawing, exploded view, installation schematic, connection modes and installation steps in the technical specifications tab, as PDF files, alongside this clamp's datasheet.
Advice from KALOT Group specialists
When you enquire, send us the diameter and material of the earth rod or reinforcing bar, the cross-section of both conductors, the direction of each conductor (in line with the earth rod or at right angles to it) and the quantity you need, and our specialists will recommend the right clamp. For ribbed reinforcing bar, state its nominal diameter.
Technical Product Information
Click to view enlarged
Feature | Value |
|---|---|
Type | Three-plate U clamp for connecting two conductors to an earth rod or reinforcing bar |
Body (three plates) | Cast brass |
U-bolt and nuts | Stainless steel |
Fastening parts | U bolt with M8 thread and two nuts |
Conductor type | Stranded copper conductor; two conductors in two separate tiers |
Earth rod or reinforcing bar diameter | 14 to 20 mm |
Cross-section of each conductor | 16 to 150 mm² |
Route of each conductor | In line with or at right angles to the earth rod; through-run or terminating |
Matching earth rod | Copper, copper-bonded or stainless steel, threaded or unthreaded |
Plate width × depth | 60 × 38.8 mm |
Weight | About 400 g |
Connection type | Bolted, can be opened and refastened |
Typical installation location | Earth inspection pit; foundation reinforcing bar before the concrete pour, or an accessible connection point |
Code | UBTV 1416 |
Three-piece U clamp code and size (UBTV)
Code | Earth rod or reinforcing bar diameter (mm) | Cross-section of each conductor (mm²) | Number of conductors | W × H (mm) |
|---|---|---|---|---|
UBTV 1416 | 14-20 | 16-150 | 2 | 60 × 38.8 |
Diameters are in millimetres and cross-sections in square millimetres; W is the plate width and H the plate depth. Our products are continually improved and some dimensions may be updated, so please confirm final dimensions with our specialists before you buy.
Dimensional drawing of the three-piece U clamp
Download the dimensional drawing (PDF)
Technical drawing
Download the technical drawing (PDF)
Exploded view
Download the exploded view (PDF)
Three plates and two conductor tiers
Three brass plates slide onto the two legs of the U bolt: the top plate, whose shallow seat rests on the earth rod or reinforcing bar, the middle plate, and the outer plate, on which the KALOT mark and the sizes "16-150" and "Ø14-20" are cast. Between each pair of neighbouring plates is one conductor tier; in each tier, the central hole takes a conductor in line with the earth rod and the transverse hole a conductor at right angles to it. In the images below, you can see the openings of the two central holes between the three plates.
Click to view enlarged
Applications of the three-piece U clamp
- Two conductors on one earth rod: connecting the down conductor of a lightning protection system and an earth ring conductor to one copper-bonded earth rod inside a concrete or polyethylene earth inspection pit
- Through-run conductor and branch: clamping a conductor that passes the earth rod and continues to the next earth rod, and taking a branch to another conductor in the same clamp, without cutting the through-run conductor
- Reinforcement bonding: connecting two copper earth conductors to foundation reinforcing bar before the concrete pour, or to reinforcing bar at a connection point that stays accessible, for bonding the structure to the earthing system
- Unthreaded or damaged earth rods: connecting two conductors to a copper or stainless steel earth rod, an unthreaded earth rod, or an earth rod whose head was damaged during driving
Installation schematic
Download the execution schematic (PDF)
Connection modes for two conductors
Download connection modes (PDF)
Installation steps for the three-piece U clamp
- Compare the diameter of the earth rod or reinforcing bar (14 to 20 mm) and the cross-section of both conductors (16 to 150 mm²) with the clamp's range.
- Before installation, clean paint, rust, mud and any non-conductive layer from the contact surfaces of the earth rod or reinforcing bar and both conductors.
- Undo the nuts, slide the three plates off the legs and pass the U bolt around the earth rod or reinforcing bar.
- Slide the top plate onto the legs so the earth rod sits in its seat. Place the first conductor in the matching hole, in line with the earth rod or at right angles to it, and put the middle plate over it.
- Place the second conductor in the second tier, on the middle plate, fit the outer plate and tighten the nuts by hand first.
- Tighten the nuts with a spanner, following the manufacturer's instructions, until both conductors are fully compressed between the plates and the clamp sits firmly on the earth rod or reinforcing bar.
- Check that both conductors are seated fully in their holes, that the three plates lie parallel to one another, and that the clamp has not damaged the earth rod, reinforcing bar or conductors. If the clamp will stay inside the concrete, photograph the connection before the pour, as it will no longer be accessible afterwards.
Download the installation steps (PDF)
Installation tools
For installation, one spanner that fits the nuts is enough; this connection needs no heat, electricity or mould.
Inspection and measurement
During periodic inspections, check the condition of the clamp, U bolt and both conductors inside the earth inspection pit, and make sure there is no corrosion, movement or loosening. If the connection is loose, corroded or damaged, open it, clean the contact surfaces and close it again following the manufacturer's instructions, or replace the clamp. To measure earth termination resistance, open the connection with a spanner so the earth rod is separated from both conductors, then close it after the measurement.
Choosing the three-piece U clamp and requesting a price
When you enquire, send us the diameter and material of the earth rod or reinforcing bar, the cross-section of both conductors, the direction of each conductor (in line with the earth rod or at right angles to it) and the quantity you need, and our specialists will recommend the right clamp. For ribbed reinforcing bar, state its nominal diameter.
Click to view enlarged
Choose this clamp when two copper conductors must reach one earth rod or reinforcing bar. With two-piece U clamps you need one clamp per conductor; the three-piece U clamp takes both conductors with one U bolt and two nuts, and each conductor is compressed separately in its own tier. The U bolt loops around the earth rod or reinforcing bar and does not rely on a thread, so it also fits ribbed reinforcing bar, unthreaded earth rods and earth rods with a damaged head. Our brass U clamp is for copper conductors and fits copper, copper-bonded or stainless steel earth rods and reinforcing bar. For a galvanised conductor or reinforcing bar, we recommend our galvanised U clamp.
Advantages of the three-piece U clamp
- Two conductors, one clamp: a down conductor and an earth ring conductor, or two bonding conductors, are fastened to the earth rod or reinforcing bar with one U bolt and two nuts.
- Each conductor in its own tier: the middle plate keeps the two conductors apart, and each one is compressed between its own two plates.
- Each conductor in line or at right angles: the route of each conductor sets its direction, and the two can run the same way or in different directions.
- On ribbed reinforcing bar and unthreaded earth rods: the U bolt closes around the earth rod or reinforcing bar and needs no thread or flat head. Neither the earth rod nor the conductors are drilled.
- Can be opened and closed: for inspection, resistance measurement or rerouting the conductors, you undo the nuts and tighten them again.
Three-piece or two-piece U clamp?
Feature | three-piece U clamp | Two-piece U clamp |
|---|---|---|
Number of conductors | Two conductors | One conductor |
Number of plates | Three brass plates | Two brass plates |
Earth rod or reinforcing bar diameter (mm) | 14 to 20 | 9.5 to 20 in six codes |
Conductor cross-section (square millimetres) | 16 to 150 for each conductor | 6 to 300 in six codes |
Conductor direction | Each conductor in line or at right angles | In line or at right angles |
Material | Brass; U bolt and nuts in stainless steel | Brass; U bolt and nuts in stainless steel |
For one conductor, or a conductor smaller than 16 or larger than 150 mm², see the two-piece U clamp in six codes; for two conductors on one 14 to 20 mm earth rod or reinforcing bar, choose this clamp. Both make a connection you can open and close; for connections buried in soil, we recommend exothermic welding.
If these conditions apply to you, see these clamps as well
Clamp | When |
|---|---|
U clamp for connecting conductor to earth rod and reinforcing bar (two-piece) | When you are fastening just one conductor to an earth rod or reinforcing bar. |
When you fasten a conductor of up to 120 mm² on the top of an earth rod with a single bolt. | |
Galvanised U clamp for connecting conductor to earth rod or reinforcing bar | When the conductor or reinforcing bar is galvanised. |
When the conductor is a tape, not a wire. | |
Reinforcing bar bonding plate with conductor for concrete structures | When the reinforcement of a concrete structure needs a brass connection point for the earthing system. |
Compare all our earthing clamps in the "Which clamp should we choose?" table.
The KALOT Group three-piece U clamp is designed and manufactured in line with IEC 62561-1, the standard that sets requirements for lightning protection system connection components, including clamps.
IEC 60364-5-54 accepts connecting an earth conductor to an earth electrode with a suitable clamp or mechanical connector, alongside exothermic welding and compression joints, provided the clamp is installed following the manufacturer's instructions and does not damage the electrode or conductor.
IEC 62305-3 treats clamping as one of the accepted connection methods in a lightning protection system. It also recommends a test joint where the down conductor meets the earthing system, which can be opened with a tool for measurement and stays closed in normal use.
In Iran, Part Thirteen of the National Building Regulations places the top of the earth rod of a simple earth electrode inside a covered pit and accepts its connection to the earthing conductor by a dedicated clamp or by welding. The same part requires the clamp, earth rod and conductor materials to be compatible, and connections to be checked for tightness and corrosion during periodic inspections. The Earthing System Safety Code also requires the connection material to be compatible with the electrode and conductor. To learn more, see standards for the design and installation of earthing systems.
Three-plate U-bolt clamp, two wires to earth rod and rebar
Documents & Downloads
Catalogues & datasheets
Drawings & schematics
- Dimensional drawing of the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
- Technical drawing of the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
- Exploded view of the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
- Installation schematic of the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
- Connection modes of the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
- Installation steps for the three-piece U clamp for connecting two conductors to earth rod and reinforcing barLanguage: Persian (opens in a new tab)
Frequently Asked Questions
What is a three-piece U clamp and how does it differ from a two-piece U clamp?
The three-piece U clamp is a brass fitting with a U bolt that fastens two copper earth conductors to one earth rod or reinforcing bar at the same time. A two-piece U clamp has two plates and takes one conductor; the three-piece version adds a middle plate, which gives it two conductor tiers, with each conductor held between two plates. For a single conductor, see our two-piece U clamp.
Can a three-piece U clamp connect two conductors to one earth rod?
Yes, that is the main job of this clamp. The first conductor sits between the top plate and the middle plate, the second between the middle plate and the outer plate, and tightening the two nuts compresses both. For example, you can fasten a lightning protection system down conductor and an earth ring conductor to one earth rod with a single clamp.
Which earth rod and conductor sizes does this clamp suit?
The clamp with code UBTV 1416 takes an earth rod or reinforcing bar of 14 to 20 mm and copper conductors of 16 to 150 mm² each; these ranges are cast on the outer plate. For a smaller or larger conductor, or a slimmer earth rod, see the two-piece U clamp codes. For sizes at the limit of the range, our specialists will recommend the right clamp.
Can the two conductors be fastened in different directions?
Yes. Each conductor tier has a central hole for a conductor in line with the earth rod and a transverse hole for a conductor at right angles to it. You can therefore fit both conductors in line, both at right angles, or one of each. For example, the down conductor comes down in line with the earth rod, while the earth ring conductor runs at right angles to it towards the next earth rod.
Can the three-piece U clamp be fitted on ribbed reinforcing bar?
Yes. The U bolt loops around the ribbed reinforcing bar, the bar sits in the seat of the top plate, and the two conductors are clamped between the plates. You can fit it inside the foundation reinforcement cage before the concrete pour, or at a point that stays accessible for inspection. If the clamp will stay inside the concrete, tighten the nuts firmly and photograph the connection before pouring.
Can a conductor pass through the clamp, or must it end there?
Both are possible, and you choose separately for each conductor. You can run one conductor through the clamp and on to the next earth rod, and terminate the second conductor in the same clamp. This way you take a branch from a continuous conductor without cutting it.
What is the three-piece U clamp made of?
The three plates are cast brass, and the U bolt and nuts are stainless steel. Our brass U clamp is for copper conductors and for copper, copper-bonded or stainless steel earth rods and reinforcing bar. For a galvanised conductor or reinforcing bar, see our galvanised U clamp, because galvanised steel in contact with copper can suffer galvanic corrosion.
Should the three-piece U clamp connection to the earth rod go inside an earth inspection pit or underground?
This clamp belongs at accessible points, such as a concrete or polyethylene earth inspection pit, so you can see it, open it for measurements and close it again. Make connections that go underground permanent with exothermic welding.
What is the code of the three-piece U clamp, and what details should we send for a quotation?
The code of this clamp is UBTV 1416: UBTV identifies the three-plate U clamp, and the digits give the minimum earth rod diameter (14) and the minimum conductor cross-section (16), following the same system as the two-piece U clamp codes. When you enquire, send us the diameter and material of the earth rod or reinforcing bar, the cross-section of both conductors, the direction of each conductor (in line with the earth rod or at right angles to it) and the quantity you need, and our specialists will recommend the right clamp. For ribbed reinforcing bar, state its nominal diameter.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.



