KALOT Group
This translation is an AI-assisted draft pending human review. It is not indexed for search yet.Read the reviewed Persian original
Earthing and bonding clamps

Complete Product Overview

Galvanised clamp for connecting tape to earth rod and round wire

Last updated:

The galvanised tape-to-earth rod clamp from KALOT Group fixes galvanised steel tape to a round steel conductor in foundation earthing and bonding, before the pour: galvanised round wire, reinforcing bar or a stainless steel earth rod. The round conductor is held in the saddle of the upper plate and the tape between two flat plates. Both pass between the two bolts, parallel or at a slight angle, and the tape is neither drilled nor cut.

The clamp is the same material as galvanised tape and round wire and also works next to stainless steel conductors, but not next to copper, since contact with copper can destroy the zinc coating. For copper tape on a copper earth rod, we recommend our brass A-type clamp. The clamp with code TRCG 3016 fixes tape up to 30 mm wide to 8 and 10 mm round wire and to reinforcing bar or an earth rod up to 16 mm. Our specialists are with you in choosing the size and requesting a quote.

Connecting galvanised tape to reinforcing bar, round wire and earth rods

To choose this clamp, weigh three things: the material of both conductors (galvanised or stainless steel), the width and thickness of the tape and diameter of the round conductor, and the location of the joint (inside concrete or in air).

  • Foundation earthing and bonding, inside concrete
  • Tape up to 30 mm to round conductor 8 to 16 mm
  • Round wire, reinforcing bar or earth rod; parallel or at a slight angle
  • Three galvanised steel plates, two M8 bolts
  • Tape between flat plates, round conductor in the saddle

    Each conductor has its own place: the round conductor is held in the saddle and the tape between two flat plates, while the middle flat plate keeps them apart. You will find the shape and order of the plates in the technical specifications tab.

  • Connecting tape to round wire and reinforcing bar in foundation earthing

    In a foundation earth electrode, galvanised tape runs as a closed ring in the building's foundations. Before the pour, this clamp connects the tape to the reinforcing bars and to the round wires that lead to the down conductors and connection terminals.

  • Material: galvanised steel, matching the tape and round wire

    The plates, bolts and nuts are all galvanised steel. The clamp matches galvanised tape and round wire, and also works with reinforcing bar and stainless steel conductors.

  • Code TRCG 3016 and drawings

    The dimensional drawing and technical drawing show the tape and round conductor range, the execution schematic shows where the clamp goes in the foundation, and the installation steps show the sequence of work. You have them all in the technical specifications tab and as PDF files, alongside this clamp's datasheet.

    Galvanised tape-to-earth rod clamp datasheet (PDF)
  • Advice from KALOT Group specialists

    Send us the tape and round conductor sizes and the joint location, and our specialists will tell you the right clamp and the price.

Technical Product Information

Click to view enlarged

Feature

Value

Type

Three-plate bolted clamp for connecting tape to a round conductor

Material

Galvanised steel (plates, bolts and nuts)

Plates

One saddle plate for the round conductor and two flat plates for the tape, all three of one design with two bolt holes

Saddle

Round and straight, perpendicular to the plate length, across its full width and between the two holes

Bolts

Two M8 hexagon bolts, property class 8.8

Nuts

Two M8 hexagon nuts

Suitable tape

Width 25 to 30 and thickness 3 to 3.5 mm: 25 × 3 (for tape inside concrete), 30 × 3 and 30 × 3.5

Suitable round conductor

8 and 10 mm galvanised round wire, reinforcing bar up to 16 mm in diameter over the ribs, and 16 mm stainless steel earth rod

Conductor materials

Galvanised or stainless steel tape; galvanised steel round wire, reinforcing bar or stainless steel earth rod

Arrangement of the two conductors

Parallel or at a slight angle to each other; both pass between the two bolts

Conductor route

Through-run or terminating; the tape is neither drilled nor cut

Do not use with

Copper or copper-coated conductor, tape or earth rod

Connection type

Bolted, can be opened and refastened

Main application

Foundation earthing and bonding, inside concrete

Other locations

In air, where galvanised tape and round wire meet

Code

⁦TRCG 3016⁩

Code and size range (TRCG)

Code

Tape width (mm)

Tape thickness (mm)

Round conductor diameter (mm)

Bolts and nuts

Number of plates

⁦TRCG 3016⁩

⁦25-30⁩

⁦3-3.5⁩

⁦8-16⁩

⁦2 × M8⁩

⁦3⁩

Diameters and dimensions are in millimetres, and ribbed reinforcing bar is measured over the ribs. Dimensions may change without prior notice; send us your project's tape and round conductor sizes so that our specialists can confirm the right clamp. Our products are continually improved and some dimensions may be updated, so please check the final dimensions with our specialists before you buy.

Dimensional drawing

Dimensional drawing of the galvanised clamp for connecting tape to earth rod and round wire, with the jaw arrangement and size table.

Download the dimensional drawing (PDF)

Technical drawing

Technical drawing of the saddle jaw and flat jaw of the galvanised clamp for connecting tape to earth rod and round wire.

Download the technical drawing (PDF)

Exploded view

Exploded view of the galvanised clamp for connecting tape to earth rod and round wire, with parts list.

Download the exploded view (PDF)

Saddle plate and flat plates

At its centre, the saddle plate has a round saddle formed straight and perpendicular to the plate length, across its full width and between the two bolt holes; the round conductor sits in this saddle. The two flat plates share the saddle plate's design and size, and the tape goes between them. Working from the bolt head side, the parts assemble in this order: saddle plate, round conductor, middle flat plate, tape, outer flat plate and nuts. The middle flat plate is always between the two conductors, and both conductors pass through the space between the two bolts.

Galvanised tape and reinforcing bar, both passing between the clamp's two bolts.
Galvanised tape and round wire, almost aligned, both passing between the clamp's two bolts.

Galvanised clamp, tape to earth rod and round wire

Drag to rotate; scroll to zoom.Open full screen

Frequently Asked Questions

What is a galvanised tape-to-earth rod clamp (galvanised tape clamp), and what does it connect?

The galvanised tape-to-earth rod clamp is a bolted fitting in galvanised steel that joins steel tape to a round steel conductor: galvanised round wire, reinforcing bar or a stainless steel earth rod. The round conductor is held in the saddle of the upper plate and the tape between two flat plates. Its main use is foundation earthing and bonding, inside the concrete and fitted before the pour.

How do we connect galvanised tape to round wire?

With this very clamp, also known in the market as a "round wire to tape clamp". Place the round wire in the saddle of the saddle plate and the tape between the two flat plates, so that both pass between the two bolts and run parallel or at a slight angle to each other. Then tighten the nuts following the manufacturer's instructions. Our galvanised steel round wire is the same material as the galvanised tape and this clamp.

Which sizes of tape, round wire and earth rod does this clamp suit?

The clamp with code TRCG 3016 takes tape 25 to 30 wide and 3 to 3.5 mm thick: 25 × 3 (for tape inside concrete), 30 × 3 and 30 × 3.5. Its round conductor can be 8 or 10 mm galvanised round wire, reinforcing bar up to 16 mm in diameter over the ribs, or a 16 mm stainless steel earth rod. In this application the galvanised tape stays inside concrete or in air, not in soil. 30 × 3.5 is among the most common galvanised tapes in earthing systems. The 8 mm round wire is used mostly for down conductors and roof networks, and the 10 mm round wire inside foundation concrete. For a larger reinforcing bar or earth rod, see the galvanised U clamp. If your project sizes sit near the limits of these ranges, our specialists will recommend the right clamp.

Can this clamp join tape and round wire (or an earth rod) both in parallel and crossing?

The tape and the round conductor both pass through the space between the two bolts, so this clamp joins them parallel or at a slight angle to each other, not crossing at right angles. If the two conductors run perpendicular to each other, bend the round wire slightly at the joint so that it lines up with the tape along the clamp. In a reinforcement cage, choose the reinforcing bar that runs in line with the tape. For a vertical earth rod, bend the end of the tape so that it rises alongside the earth rod. For a 90-degree crossing of two galvanised round wires, see our galvanised cross clamp.

Why does this clamp have three plates, and where do the tape and round conductor go?

Because each conductor has its own place. The round conductor sits in the saddle of the saddle plate, on the bolt head side. After it come the middle flat plate, then the tape, and finally the outer flat plate and the nuts. The middle plate keeps the two conductors apart, so that the round conductor in the saddle and the flat tape between two flat surfaces are each clamped separately.

Does installing this clamp require drilling the tape or welding?

No. The tape is not drilled and its cross-section stays intact. Two spanners are enough for installation, with no need for welding, heat or electricity. We made this clamp for joints inside concrete and in air. Make joints that must be buried directly in soil permanent with exothermic welding.

Can this clamp connect galvanised tape to a copper or copper-bonded earth rod, or to the copper conductor of an earth pit?

No. Connecting galvanised tape to a copper-bonded earth rod in soil is a common site mistake: in moisture, the zinc coating next to copper can corrode quickly, and fine particles shed by a copper part higher up damage the galvanised part even without contact. The same goes for a copper conductor or copper plate in an earth pit. You have two sound options: build the whole system in copper and fix copper tape to the earth rod with our brass A-type clamp, or choose a stainless steel earth rod so that this clamp can connect it to the galvanised tape. To tie an existing copper system into the foundation, consult our specialists before starting work.

Can this clamp also be used with a stainless steel earth rod or stainless steel tape?

Yes. Unlike copper, stainless steel can be used next to galvanised steel in concrete and in air, and the standards recommend that an electrode running from foundation concrete into soil be made of stainless steel. So you can fix galvanised tape inside concrete to a 16 mm stainless steel earth rod with this clamp. This is a joint between two dissimilar metals: place it inside concrete or somewhere dry above ground level, not in soil, and cover it fully with a moisture-proof compound or tape before the pour or in air. If the head of the earth rod is inside an inspection pit, do not make this joint there, because the pit is in contact with soil and moisture. Connect the galvanised tape to a stainless steel branch inside the concrete, so that only stainless steel reaches the pit. If both conductors are stainless steel and you are joining 50 or 70 mm² conductor to 20 × 3 or 30 × 2 tape at right angles, see the multi-purpose stainless steel four-way clamp. For a stainless steel earth rod with stainless steel tape, consult our specialists.

Where should the galvanised foundation tape be joined to an earth rod or a conductor going into soil?

Inside the concrete, with at least 5 cm of cover, so that only stainless steel leaves the concrete: not at the boundary between concrete and soil, and not in soil. A galvanised conductor or joint must not pass straight from concrete into soil. Make any joint that has to be buried in soil with exothermic welding. If the project is in a coastal area or has saline groundwater, consult our specialists before using galvanised parts.

Can this clamp connect the foundation electrode tape to the round wire leading to a test joint or down conductor?

Yes. Galvanised round wire that rises inside a concrete column or wall and reaches the test joint or the down conductor of the lightning protection system sits in the saddle of this clamp, with the foundation tape between the two flat plates. For down conductors, 8 mm round wire is common. Bring this round wire out into the air on the surface of the column or wall or inside the building, not through soil, and mark and protect its end until the work is finished.

What is the code of the galvanised tape-to-earth rod clamp, and what information should we send for a quote?

The code of this clamp is TRCG 3016: TRCG denotes the galvanised clamp connecting tape to a round conductor, 30 is the maximum tape width and 16 the maximum round conductor diameter. When requesting a quote, send us the material and size of the tape (width × thickness), the type, material and diameter of the round conductor (round wire, reinforcing bar or earth rod), the arrangement of the two conductors (parallel or at an angle), the location of the joint (inside concrete or in air), the quantity and, if you have it, the foundation earthing drawing. Our specialists will tell you the right clamp and its price.

Does this clamp also connect galvanised tape to foundation reinforcing bars?

Yes. The ribbed reinforcing bar sits in the saddle of the saddle plate and the tape between the two flat plates. What counts is the bar diameter over the ribs, which must not exceed 16 mm: that means bar number 12 and thinner. Fix the tape to a reinforcing bar running in line with it, and for joints that stay in concrete, connect the tape with two clamps to two separate bars, because these joints can no longer be inspected after the pour. For a larger reinforcing bar, see the galvanised U clamp (reinforcing bar 14 to 34 mm).

How many of these clamps does a building's foundation earthing need?

Count them from the foundation earthing drawing: every point the designer has set for connecting tape to reinforcement (for a joint that stays in concrete, two clamps on two reinforcing bars), every branch reaching a down conductor or test joint, every branch or terminal leaving the concrete, and every stainless steel earth rod. The designer sets the spacing of the connections to the reinforcement according to earthing and lightning protection standards. Keep a few extra clamps for site changes as well.

Should we tie the tape to the reinforcing bar with tie wire, weld it or use a clamp?

Tie wire only holds the tape in place until the pour. Lightning protection standards do not consider such a connection sufficient for lightning current and require the electrical connection to be made by clamp or weld. Welding on reinforcing bar needs the structural designer's agreement and a skilled welder. This clamp goes on beside the formwork and reinforcement without welding or heat, can be inspected before the pour, and can be undone and moved if it is in the wrong place. So hold the tape along its route with tie wire and fit this clamp at the connection points set by the designer. If the designer has asked for a permanent welded joint, see connection by exothermic welding.

Have a Technical Question?

KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.