KALOT Group
This translation is an AI-assisted draft pending human review. It is not indexed for search yet.Read the reviewed Persian original
Earthing and bonding clamps

Complete Product Overview

One-piece clamp for connecting conductor to plates and metal structures (TECS)

Last updated:

The KALOT Group one-piece clamp for connecting conductor to plates and metal structures (code TECS) presses a copper earth conductor or lightning protection conductor directly onto a plate, column, beam, angle or building steel frame. The clamp is a single cast brass clamping plate with a conductor groove along its edge. A stainless steel bolt passes through the holes in the clamping plate and structure and, as the nut tightens, the plate presses the conductor onto the metal surface.

Because the conductor sits directly on the metal of the structure, the one-piece clamp is the simplest, lowest-profile way to connect an earth conductor to a steel frame, provided the surface is clean and flat at the contact point. We make it in two sizes: for 16 to 70 mm² conductors with an M8 bolt, and for 95 to 185 mm² conductors with an M10 bolt. If you want the conductor held between two brass clamping plates with no direct contact with the structure's surface, see the two-piece conductor-to-structure clamp (TECD).

One-piece clamp for direct connection of earth conductors to steel frames

To choose a one-piece clamp, check the conductor cross-section and make sure the structure's surface is clean and flat at the connection point. The code follows from the conductor, and the bolt length from the thickness of the structure.

  • Direct connection of copper conductor to plates and steel frames
  • Conductors from 16 to 185 mm² in two sizes
  • One cast brass clamping plate, stainless steel bolt and nut
  • Low profile, one hole in the structure
  • Direct conductor-to-metal contact

    The brass clamping plate presses the conductor directly onto the plate or column, so current passes straight from conductor to structure.

  • Low profile and simple

    Just one clamping plate, one bolt and one nut, installed with a single hole in the structure.

  • Material: brass and stainless steel

    The clamping plate is cast brass and the bolt and nut are stainless steel. Brass is compatible with copper conductors and the bolt resists corrosion.

  • Two TECS sizes and drawings

    You will find codes TECS 1670 and TECS 9518, with conductor range, conductor diameter and bolt size, in the technical specifications tab. The clamp's shape is shown in the dimensional drawing, technical drawing, exploded view and datasheet of the one-piece clamp.

    One-piece clamp datasheet (PDF)
  • Advice from KALOT Group specialists

    When you enquire, send us the conductor cross-section, the type and thickness of the plate or structure (column, beam, angle, earth plate), whether it is painted or galvanised, and the quantity you need. Our specialists will confirm the right code, bolt length and price.

Technical Product Information

Click to view enlarged

Feature

Value

Type

One-piece clamp for direct connection of one copper conductor to a plate or steel structure

Body

One trapezoidal cast brass clamping plate with a conductor groove along the wider edge

Bolts and nuts

Stainless steel: one hex bolt passing through the clamping plate and the hole in the structure, with a nut behind the structure

Suitable conductor

Stranded or solid copper conductor: earth conductor, bonding conductor or lightning protection down conductor

Conductor range

16 to 70 and 95 to 185 mm², in two sizes

Bolts and nuts

M8 × 35 for TECS 1670 and M10 × 50 for TECS 9518

Installation location

Plates, columns, beams, angles, earth plates and accessible steel structures with a clean, flat contact surface

Connection type

Bolted, can be opened and refastened

Codes

TECS 1670 and TECS 9518

One-piece clamp sizes and codes (TECS)

Code

Conductor cross-section (mm²)

Conductor diameter on the drawing (mm)

Bolts and nuts

⁦TECS 1670⁩

⁦16-70⁩

⁦5.1-10.7⁩

⁦M8 × 35⁩

⁦TECS 9518⁩

⁦95-185⁩

⁦12.6-17.6⁩

⁦M10 × 50⁩

Cross-sections are in square millimetres. "Conductor diameter on the drawing" is the diameter of the conductors drawn for each size in our manufacturing drawings. The bolt length of each size is set for the usual thickness of plates and angles. If your structure is thicker, tell us its thickness when you enquire. We continually improve our products and some dimensions may be updated, so please confirm the final dimensions with our specialists before you buy.

One-piece clamp for connecting conductor to structure, for wire of 16 to 70 mm², from three views.
One-piece clamp for connecting conductor to structure, for wire of 95 to 185 mm², from three views.

Dimensional drawing

Dimensional drawing of the one-piece clamp for connecting conductor to structure, with code table.

Download the dimensional drawing (PDF)

Technical drawing

Technical drawing of the one-piece clamp for connecting conductor to structure.

Download the technical drawing (PDF)

Exploded view

Exploded view of the one-piece clamp for connecting conductor to structure, with parts list.

Download the exploded view (PDF)

KALOT AutoCAD drawing

AutoCAD drawing of the one-piece clamp for connecting conductor to structure: three-dimensional installation view and front and side views.

Download the AutoCAD drawing (PDF)

Conductor groove and contact with the structure

Along its wider edge, the clamping plate has a semicircular groove facing the structure. The conductor lies in this groove on the surface of the structure, the bolt passes through the central hole of the plate and the hole in the structure, and the nut is tightened behind the structure. As the nut tightens, the plate acts like a lever and presses the conductor onto the metal. Because the conductor is in direct contact with the surface, the cleanliness of that surface plays the main part in the quality of the connection.

One-piece clamp for connecting conductor to structure from the isometric view; the brass jaw holds the copper wire directly on the galvanised steel plate.
One-piece clamp for connecting conductor to structure from the front; the stainless steel hex bolt is in the middle of the jaw and its nut is tightened behind the plate.

One-piece clamp, wire to metal plates and structures

Drag to rotate; scroll to zoom.Open full screen

Frequently Asked Questions

What is a one-piece conductor-to-plate clamp?

It is a one-piece brass clamp that uses a single stainless steel bolt to press a copper earth or lightning protection conductor directly onto a steel plate, column, beam or angle. The conductor is held between the groove of the clamping plate and the surface of the structure.

Which clamp should we use to connect an earth conductor to a building's steel frame?

If the surface of the column or plate can be cleaned back to bare metal, the one-piece clamp is the simplest route. If the conductor needs to be held between two clamping plates, or the frame will be clad, choose the two-piece clamp. Both install with a single hole in the structure.

Which one-piece clamp size should I choose?

Choose the size by conductor cross-section: TECS 1670 for 16 to 70 mm² conductors with an M8 × 35 bolt, and TECS 9518 for 95 to 185 mm² conductors with an M10 × 50 bolt.

Why does cleaning the structure's surface matter so much with a one-piece clamp?

Because the conductor is pressed directly onto that surface, any paint, rust or grease between conductor and metal raises the resistance of the connection. Clean the area under the conductor and clamping plate back to bare metal and, once tightened, cover the joint with paint or a moisture-proof compound.

Can it be installed on galvanised structures as well?

Yes. On galvanised structures, remove only dirt and grease and do not scrape off the zinc coating. Since copper and brass are dissimilar to galvanised steel, cover the joint with paint or a moisture-proof compound after tightening so that moisture cannot reach the contact point.

What conductor diameter is the one-piece clamp made for?

In our manufacturing drawings, the 16 to 70 size is drawn for conductors of about 5 to 11 mm in diameter, and the 95 to 185 size for conductors of about 13 to 18 mm. If your conductor falls between these two ranges, tell our specialists its cross-section and type.

How does the thickness of the column or plate affect the choice?

The bolt passes through the clamping plate and the structure itself, so the thicker the structure, the longer the bolt must be. The bolt length of each code is set for common plates and angles. For a thick column or plate, tell us the thickness when you enquire.

Can the one-piece clamp be used below ground?

No. This clamp is for accessible connections on structures, so it can be seen and retightened. For connections below ground, we recommend exothermic welding.

What should we do for conductors larger than 185 mm²?

The one-piece clamp is made for conductors up to 185 mm². For larger conductors, or where two large conductors reach the structure at one point, see the single-bolt parallel clamp or talk to our specialists.

Can we also connect a tape conductor to a plate with this clamp?

The one-piece clamp is made for conductors and round wire. For copper tape, see the tape-to-metal plate bonding clamp.

Have a Technical Question?

KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.