Move your pointer over the image to zoom in
Complete Product Overview
Two-piece brass clamp for fixing conductor to walls
Order Code: HDCC 050 · HDCC 070 · HDCC 095
Last updated:
The KALOT two-piece brass clamp for fixing conductors to walls (Heavy Duty Cast Cable Saddle) holds round stranded copper conductors firmly and neatly on walls and building surfaces, along lightning protection down conductor and earthing routes.
We manufacture this clamp in three models: HDCC 050 for 50 mm², HDCC 070 for 70 mm² and HDCC 095 for 95 mm² conductors. The body is two cast brass pieces closed with two stainless steel bolts. The conductor sits in the passage under the clamp's central raised section and is held between the two pieces as the bolts tighten.
Dimensions: 52 × 20 mm, height 21 mm (model HDCC 095: 24 mm). The K A mark is cast onto the clamp's raised section.
A firm holder for round conductors on facades
Down conductors and earth conductors must stay firm and free of sagging along their whole route on the building surface, so that wind, impact and the electrodynamic forces of lightning current do not shift them. The KALOT two-piece brass clamp is made for exactly this job: a heavy cast body, two stainless steel bolts and a passage matched to the conductor cross-section.
Two-piece design, held by two bolts
The conductor sits between two brass pieces and, as the two end bolts tighten, it is held evenly without damaging the strands.
Three models for three cross-sections
Model HDCC 050 for 50 mm², HDCC 070 for 70 mm² and HDCC 095 for 95 mm² conductors; the conductor sits exactly in the clamp's passage.
Cast brass and stainless steel bolts
The brass body is compatible with copper conductors, and the stainless steel bolts keep their durability outdoors and on building facades.
Restraint against wind and lightning current forces
The heavy cast body keeps the conductor on its route, even on tall facades and in windy areas.
For down conductors and earthing routes
On facades, parapets and concrete, brick or stone walls, wherever a round stranded copper conductor must stay tidy and easy to inspect.
Technical Product Information
Feature | Value |
|---|---|
Product type | Two-piece conductor-to-wall clamp (Heavy Duty Cast Cable Saddle) |
Application | Holding round stranded copper conductors on walls and building surfaces |
Conductor | Round stranded copper |
Conductor cross-section | HDCC 050: 50; HDCC 070: 70; HDCC 095: 95 mm² |
Body material | Brass (cast) |
Bolts | 2 pieces, stainless steel |
Structure | Two pieces: base and top piece with central raised section and conductor passage |
Wall fixing | The lower piece (base) fixes to the wall with a screw and wall plug. The top piece sits over the conductor and closes onto the base with two stainless steel bolts. |
Dimensions | L = 52 mm, W = 20 mm, H = 21 mm (model HDCC 095: H = 24 mm) |
Marking | K A on the clamp's raised section |
Order code | HDCC 050 , HDCC 070 , HDCC 095 |
Our products are continually improved and some dimensions may be updated; please confirm the final dimensions with our specialists before you buy.
Order code | Conductor cross-section (mm²) | L (mm) | W (mm) | H (mm) |
|---|---|---|---|---|
HDCC 050 | 50 | 52 | 20 | 21 |
HDCC 070 | 70 | 52 | 20 | 21 |
HDCC 095 | 95 | 52 | 20 | 24 |
Choose the model by the conductor cross-section, so the conductor sits exactly in the clamp's passage and is held firmly as the bolts tighten. For large orders or conductors with other cross-sections, our experts at KALOT Group will gladly guide you.
Click to view enlarged
The KALOT dimensional drawing shows three views of the clamp: the front view with base, top piece, central raised section and conductor passage; the top view with the K A mark and two bolts; and the side view. Dimensions: L = 52 mm · W = 20 mm · H = 21 / 24 mm. The PDF and SVG files of this drawing are in the "Documents and downloads" section of this page.
Click to view enlarged
Application
- holding round stranded copper down conductors on the building facade, from the roof to the test joint;
- restraining horizontal conductors on parapets and roof walls;
- holding earth and bonding conductors on walls, ducts and structures.
Clamp spacing along the conductor route
The number and spacing of clamps are set by the system designer and depend on the type of system, the building height and wind conditions. Two references common on projects in Iran recommend the following:
System type and installation location | Clamp spacing |
|---|---|
ESE air terminal, down conductor (NF C 17-102) | Three clamps per metre (every 33 cm) |
Conventional system, down conductor up to a height of 20 metres; common guidance based on IEC 62305-3 | Maximum 1 m |
Conventional system, down conductor above 20 m | Maximum 0.5 m |
Horizontal conductor on a roof, parapet or wall | Maximum 0.5 m |
Before and after every bend and every connecting clamp, fit one clamp closer (about 30 cm) so the conductor does not shift at these points.
Installation sequence
- Choose the clamp model by the conductor cross-section (HDCC 050, HDCC 070 or HDCC 095).
- Mark the conductor route on the wall and mark the clamp positions according to the design spacing.
- Fix the clamp bases to the surface with screws and wall plugs suited to the wall material.
- Place the conductor in the clamp passage without twisting or stretching it.
- Put the top piece over the conductor and tighten the two stainless steel bolts gradually and evenly until the conductor is held firmly.
- Finally, inspect the route to check that the conductor is straight and all clamps are firm.
Choosing the right clamp for round conductors
- Round stranded copper conductor from 50 to 95 mm² with a cast brass clamp: this clamp, HDCC 050 / HDCC 070 / HDCC 095.
- Two-piece stainless steel sheet clamp: two-piece stainless steel clamp for fixing conductor to walls.
- Light single-bolt clamp: one-hole clip for fixing conductors to walls.
- PVC-sheathed conductor: insulated one-hole clip for fixing conductors and cables to walls.
- When the conductor must run clear of the wall: BPH 76 down conductor stand-off base.
Technical notes
- The brass body is compatible with copper conductors. For aluminium or galvanised steel conductors, use a clamp of the same material as the conductor.
- Tighten the bolts evenly: overtightening crushes the conductor strands, and loose bolts leave the conductor free in the wind.
- This clamp is a mechanical holder. To connect conductors to each other electrically, use KALOT connecting clamps.
The following standards set out the requirements for conductor fasteners and their installation spacing in lightning protection systems:
IEC 62561-4 (conductor fasteners)
This standard sets the requirements and tests for conductor fasteners in lightning protection systems, including mechanical strength and durability under environmental conditions.
IEC 62305-3 (system design and installation)
Down conductors must be restrained so that the electrodynamic forces of lightning current and mechanical forces such as wind do not break or loosen them. The designer sets the clamp spacing on this basis.
NF C 17-102 (ESE air terminals)
In ESE systems, the down conductor is restrained on the building surface with three clamps per metre. Read the key points of the NFC 17-102 standard in this article.
Round conductor holding clamps for walls
Frequently Asked Questions
What is a two-piece brass conductor-to-wall clamp used for?
This clamp holds round stranded copper conductors firmly and neatly on walls and building surfaces along lightning protection down conductor and earthing routes.
Which model should I choose for my conductor?
Model HDCC 050 for 50 mm², HDCC 070 for 70 mm² and HDCC 095 for 95 mm² conductors. The right model lets the conductor sit exactly in the clamp's passage and be held firmly.
How far apart should the clamps be on a down conductor?
The system designer sets the final spacing. In ESE air terminal systems, three clamps per metre is common; in conventional systems, the maximum for a down conductor is 1 metre up to a height of 20 metres and 0.5 metre above that.
What are the clamp and bolts made of?
The clamp body is cast brass and its two bolts are stainless steel.
Which is better for an earth conductor, a brass or a stainless steel clamp?
For copper conductors, a cast brass clamp belongs to the same material family and has a heavier body. We also offer a stainless steel sheet version for 50 and 70 mm² conductors; the choice depends on the project design and the client's preference.
Is this clamp suitable for a PVC-sheathed conductor?
This clamp is made for bare round stranded copper conductors. For sheathed conductors, use the KALOT insulated one-hole clip.
Does this clamp create an electrical connection?
No. This clamp is a mechanical holder for the conductor on the wall. To join conductors to each other, use KALOT conductor-to-conductor or conductor-to-tape clamps.
Which surfaces can the clamp be installed on?
On concrete, brick and stone walls and other building surfaces, using screws and wall plugs that suit that surface.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.



