Move your pointer over the image to zoom in
Complete Product Overview
Two-piece brass clamp for fixing tape to walls
Order Code: DCC 253 · DCC 303
Last updated:
KALOT's two-piece brass clamp for fixing tape to walls (Tape DC Clip) holds the copper tape of down conductors and roof conductors firmly and neatly on walls and building surfaces.
The clamp is made of two forged brass pieces. The base piece is fixed to the wall through its central hole with a screw and wall plug, the tape sits on it, and the top piece is fastened onto the base with two stainless steel screws so that the tape is held in the groove between the two pieces.
We manufacture this clamp in two models: DCC 253 for 25×3 tape and DCC 303 for 30×3 mm tape. The name KALOT ABHAR is engraved on the top piece.
Three clamps per metre, a tape that always stays in place
A tape down conductor rests its weight on the clamps along the whole facade and must not shift under wind or the forces of lightning current. That is why systems designed to NF C 17-102 use three clamps per metre. KALOT's two-piece brass clamp, with its forged body and two stainless steel screws, is made for exactly this job.
Two pieces, step-by-step installation
First the base piece is fixed to the wall, then the tape is laid on it and the top piece is fastened with two screws, so adjusting the tape route is simple.
Forged brass and stainless steel screws
The brass body is compatible with copper tape, and the stainless steel screws prevent corrosion and loosening of the joint outdoors.
Two models for common tapes
DCC 253 for 25×3 tape and DCC 303 for 30×3 mm tape. The tape sits precisely in the clamp's groove.
Firm hold against wind and tape weight
The mechanical strength of the body carries the weight of the tape on tall facades and keeps the conductor route straight and steady.
For down conductors and roof networks
On brick, concrete and stone walls, parapets and roofs, wherever copper tape must stay tidy and easy to inspect.
Technical Product Information
Feature | Value |
|---|---|
Product type | Two-piece tape-to-wall clamp (Tape DC Clip) |
Application | Holding the copper tape of down conductors and roof conductors on building surfaces |
Tape | DCC 253: 25×3; DCC 303: 30×3 mm |
Body material | Brass (forged) |
Bolts | 2 pieces, stainless steel, cross-head |
Structure | Two pieces: base piece with a central hole for wall fixing; top piece with two screws; tape in the groove between the two pieces |
Wall fixing | The base piece is fixed to the wall through the central hole with one screw and wall plug |
Dimensions | DCC 253: 50 × 20 × 10 mm; DCC 303: 60 × 20 × 10 mm |
Marking | KALOT ABHAR on the top piece |
Order code | DCC 253 , DCC 303 |
Our products are continually improved and some dimensions may be updated; please confirm the final dimensions with our specialists before you buy.
Order code | Tape (mm) | L (mm) | W (mm) | H (mm) |
|---|---|---|---|---|
DCC 253 | 25×3 | 50 | 20 | 10 |
DCC 303 | 30×3 | 60 | 20 | 10 |
Choose the model according to the tape size on your route. For other tapes or large orders, our specialists at KALOT Group will be glad to guide you.
Click to view enlarged
KALOT's dimensional drawing shows the top piece with its two screws and the KALOT ABHAR marking, the base piece with its central fixing hole and two screw holes, and a side view with the tape groove. DCC 253: L 50 · W 20 · H 10 mm; DCC 303: L 60 · W 20 · H 10 mm. PDF and SVG files are in the "Documents and downloads" section of this page.
Click to view enlarged
Installation infographic of KALOT's two-piece brass clamp on 25×3 mm copper tape: the clamps sit 33 cm apart (three clamps per metre) along the down conductor route, the base piece is fixed to the wall through its countersunk central hole with a screw and wall plug, and the top piece holds the tape in its groove with two stainless steel screws.
Click to view enlarged
Application
- Holding down conductor tape on the building facade, from the roof to the test joint;
- Holding the tapes of roof networks and parapets;
- Holding earthing and bonding tapes on walls and structures.
Clamp spacing
The system designer sets the number and spacing of clamps. Two references common in projects in Iran recommend the following:
System type and installation location | Clamp spacing |
|---|---|
ESE air terminal, down conductor (NF C 17-102) | Three clamps per metre (every 33 cm) |
Conventional system, down conductor up to a height of 20 metres; common guidance based on IEC 62305-3 | Maximum 1 m |
Conventional system, down conductor above 20 m | Maximum 0.5 m |
Horizontal conductor on a roof, parapet or wall | Maximum 0.5 m |
Installation sequence
- Choose the clamp model according to the tape size.
- Mark the tape route on the wall and mark the clamp positions according to the design spacing.
- Fix the base piece of each clamp to the surface through the central hole, using a screw and wall plug suited to the wall material.
- Lay the tape on the base pieces without twisting it.
- Place the top piece and tighten the two stainless steel screws gradually and evenly until the tape is held in the groove.
- Finally, check that the tape route is straight and that all the clamps are tight.
Choosing the right clamp for tape
- Forged brass clamp for 25×3 and 30×3 tape: this clamp, DCC 253 / DCC 303.
- Two-piece sheet stainless steel clamp for 20 to 30 mm tape: Two-piece stainless steel clamp for fixing tape to walls.
- When the tape must run at a distance from the wall: BPH 76 down conductor stand-off base.
- Continuing the tape route in line: Two-way tape-to-tape clamp.
- The test point at the bottom of the down conductor: SKADL 100 brass disconnector.
Technical notes
- The brass body is compatible with copper tape. For aluminium or galvanised steel tapes, use a clamp of the same material as the tape.
- Tighten the screws evenly. This clamp is a mechanical holder, so for the electrical connection of tapes to each other, use KALOT's connection clamps.
The following standards set out the requirements for conductor fasteners and their installation spacing:
IEC 62561-4 (conductor fasteners)
This standard sets the requirements and tests for conductor fasteners in lightning protection systems, including mechanical strength and durability under environmental conditions.
IEC 62305-3 (system design and installation)
Down conductors must be held so that the electrodynamic forces of lightning current and mechanical forces such as wind do not break or loosen them.
NF C 17-102 (ESE air terminals)
The down conductor is held on the building surface with three clamps per metre. Read the key points of the NFC 17-102 standard in this article.
Tape holding clamps for walls and roofs
Documents & Downloads
Catalogues & datasheets
Drawings & schematics
Frequently Asked Questions
What is the two-piece brass tape-to-wall clamp used for?
This clamp holds the copper tape of down conductors and roof conductors firmly and neatly on walls and building surfaces.
Which model should I choose?
DCC 253 for 25×3 tape and DCC 303 for 30×3 mm tape.
How is the clamp installed on the wall?
The base piece is fixed to the wall through its central hole with a screw and wall plug, the tape sits on top of it, and the top piece is fastened onto the base with two stainless steel screws.
How far apart should the clamps be on a down conductor?
In ESE systems, three clamps per metre, which means one every 33 cm. In conventional systems, for down conductors up to 20 m high, 1 m at most, and 0.5 m above that height. The system designer sets the final spacing.
What are the clamp and bolts made of?
The clamp body is forged brass and its two screws are stainless steel.
Which is better for fixing tape to walls, a brass clamp or a stainless steel one?
Forged brass is a natural match for copper tape and gives a strong body. We also offer a sheet stainless steel version for 20 to 30 mm tapes. The choice depends on the project design and the client's preference.
Does this clamp create an electrical connection?
No. This clamp is a mechanical holder for tape on a wall. To join tapes to each other, use KALOT's two-way tape-to-tape clamp.
Is this clamp also suitable for round conductors?
No. This clamp is made for tape. For round copper conductors, use KALOT's two-piece brass clamp for fixing conductor to walls.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.



