Move your pointer over the image to zoom in
Complete Product Overview
One-piece stainless steel clamp for fixing tape to walls
Order Code: STS 253 · STS 303
Last updated:
KALOT's one-piece stainless steel clamp for fixing tape to walls (Simple Tape Clip) keeps the tape of down conductors and roof conductors flush with the building facade, straight and firm.
The clamp is formed from a single stainless steel strip: its middle bridge sits over the tape and its two flat ends are each fixed to the wall with a screw and wall plug. Simple, with no separate piece, and held from both sides.
We manufacture this clamp in two models: STS 253 for 25×3 tape and STS 303 for 30×3 mm tape. The name KALOT ABHAR is engraved on the clamp's bridge.
One piece, two screws, a tape that never moves
A tape down conductor must stay steady along the whole facade against its own weight, wind and the forces of lightning current. That is why systems designed to NF C 17-102 use three clamps per metre. KALOT's one-piece clamp is made of stainless steel and is fixed to the wall with two screws, one on each side of the tape.
Stainless steel, strong and long-lasting
The stainless steel body is very strong and keeps its appearance and performance outdoors, in rain and sun.
Held from both sides of the tape
Two screws at the two ends of the clamp hold the tape on the wall from both sides, so the clamp does not turn and the tape route stays straight.
One piece, no extra parts
The clamp is a single piece with no separate parts, which makes it easy to work with at height and on scaffolding.
Two models for common tapes
STS 253 for 25×3 tape and STS 303 for 30×3 mm tape. The clamp's bridge sits precisely over the tape.
A natural match for stainless steel tape
The best choice for routes run with stainless steel tape, with conductor and clamp in the same material.
Technical Product Information
Feature | Value |
|---|---|
Product type | One-piece tape-to-wall clamp (Simple Tape Clip) |
Application | Holding the tape of down conductors and roof conductors flush with building surfaces |
Tape | STS 253: 25×3; STS 303: 30×3 mm |
Material | Stainless steel |
Structure | One piece: middle bridge over the tape and two flat ends, each with one fixing hole |
Wall fixing | Two screws and wall plugs, one at each end of the clamp |
Dimensions | STS 253: 62 × 16 × 5 mm; STS 303: 63 × 16 × 5 mm |
Marking | KALOT ABHAR on the clamp's bridge |
Order code | STS 253 , STS 303 |
Our products are continually improved and some dimensions may be updated; please confirm the final dimensions with our specialists before you buy.
Order code | Tape (mm) | Material | L (mm) | W (mm) | H (mm) |
|---|---|---|---|---|---|
STS 253 | 25×3 | Stainless steel | 62 | 16 | 5 |
STS 303 | 30×3 | Stainless steel | 63 | 16 | 5 |
Choose the model according to the tape size on your route. We also make other sizes and materials to order, and our specialists at KALOT Group will be glad to guide you.
Click to view enlarged
KALOT's dimensional drawing shows the front view of the clamp with its two fixing holes and the KALOT ABHAR marking on the bridge, and a side view with the tape under the bridge. STS 253: L 62 · W 16 · H 5 mm; STS 303: L 63 · W 16 · H 5 mm. PDF and SVG files are in the "Documents and downloads" section of this page.
Click to view enlarged
KALOT execution schematic: one-piece clamps on the vertical tape route, three clamps per metre (one every 33 cm), each clamp with two screws on the wall.
Click to view enlarged
Application
- Holding down conductor tape on the building facade, from the roof to the test joint;
- Holding roof network tapes on parapets and walls;
- Holding earthing and bonding tapes on walls and structures.
Clamp spacing
The system designer sets the number and spacing of clamps. Two references common in projects in Iran recommend the following:
System type and installation location | Clamp spacing |
|---|---|
ESE air terminal, down conductor (NF C 17-102) | Three clamps per metre (every 33 cm) |
Conventional system, down conductor up to a height of 20 metres; common guidance based on IEC 62305-3 | Maximum 1 m |
Conventional system, down conductor above 20 m | Maximum 0.5 m |
Horizontal conductor on a roof, parapet or wall | Maximum 0.5 m |
Installation sequence
- Choose the clamp model according to the tape size.
- Mark the tape route on the wall and mark the clamp positions according to the design spacing.
- Lay the tape on the route without twisting it and place the clamp so that its bridge sits correctly over the tape.
- Mark the two hole positions on the wall, drill them and insert wall plugs suited to the wall material.
- Tighten the two screws gradually and evenly until the clamp holds the tape firmly on the wall.
- Finally, check that the tape route is straight and that all the clamps are tight.
Choosing the right clamp for tape
- One-piece stainless steel clamp for 25×3 and 30×3 tape on walls: this clamp, STS 253 / STS 303.
- On the roof, where the tape passes over a concrete block, or when you have only one fixing point: Two-piece brass clamp for fixing tape to walls.
- Two-piece sheet stainless steel clamp for 20 to 30 mm tape: Two-piece stainless steel clamp for fixing tape to walls.
- When the tape must run at a distance from the wall: BPH 76 down conductor stand-off base.
- Tape in the same material as the clamp: KALOT stainless steel tape.
Technical notes
- The clamp is made for installation on walls and building surfaces. Where tape passes over concrete roof blocks, use KALOT's two-piece brass clamp.
- Tighten the screws evenly. This clamp is a mechanical holder, so for the electrical connection of tapes to each other, use KALOT's connection clamps.
The following standards set out the requirements for conductor fasteners and their installation spacing:
IEC 62561-4 (conductor fasteners)
This standard sets the requirements and tests for conductor fasteners in lightning protection systems, including mechanical strength and durability under environmental conditions.
IEC 62305-3 (system design and installation)
Down conductors must be held so that the electrodynamic forces of lightning current and mechanical forces such as wind do not break or loosen them.
NF C 17-102 (ESE air terminals)
The down conductor is held on the building surface with three clamps per metre. Read the key points of the NFC 17-102 standard in this article.
Tape holding clamps for walls and roofs
Documents & Downloads
Catalogues & datasheets
Drawings & schematics
Frequently Asked Questions
What is the one-piece tape-to-wall clamp used for?
This clamp holds the tape of down conductors and roof conductors flush with the wall, straight and firm on building surfaces.
Which model should I choose?
STS 253 for 25×3 tape and STS 303 for 30×3 mm tape.
What is the clip made of?
Stainless steel: strong and well suited to outdoor use.
How is the clamp installed on the wall?
The clamp sits over the tape and each of its two ends is fixed to the wall with a screw and wall plug.
How far apart should the clamps be on a down conductor?
In ESE systems, three clamps per metre, which means one every 33 cm. In conventional systems, for down conductors up to 20 m high, 1 m at most, and 0.5 m above that height. The system designer sets the final spacing.
Which is better, a one-piece clamp or a two-piece clamp?
The one-piece stainless steel clamp holds the tape from both sides with two screws and has no separate piece. The two-piece brass clamp is fixed to the wall with one screw and is also used on concrete roof blocks. The choice depends on the installation location and the project design.
Can this clamp also be installed on a concrete roof block?
This clamp is for walls and building surfaces. On concrete roof blocks, use KALOT's two-piece brass clamp.
Does this clamp create an electrical connection?
No. This clamp is a mechanical holder for tape on a wall. To join tapes to each other, use KALOT's tape-to-tape clamps.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.



