KALOT Group
This translation is an AI-assisted draft pending human review. It is not indexed for search yet.Read the reviewed Persian original
Tape-to-tape exothermic welding

Complete Product Overview

TT7 exothermic weld: overlap joint of two copper tapes

Last updated:

The TT7 exothermic weld makes an overlap joint of two copper tapes in earthing, bonding and lightning protection networks. We manufacture its graphite mould under our KALweld® brand and supply it complete with weld powder and handle. Once welded, the joint becomes one piece with the conductors, with no nuts and bolts to loosen over time. KALweld® welds have been tested to IEEE 837 and UL 467 at the Power and Water University of Technology (Shahid Abbaspour) and successfully passed the freeze, thermal cycling and short-circuit tests.

In an overlap joint, the ends of the two tapes lie one on top of the other instead of meeting edge to edge, and the weld fully encloses the overlapping section.

The TT7 mould is made for 20×3 to 60×5 mm tape. The mould and powder code for each size is in the "Mould and powder selection" table, and the HC 01 handle suits all its sizes.

Technical Product Information

Click to view enlarged

Mould body material: graphite; mould lid material: stainless steel; suitable handle: HC 01.

TT7 mould and powder selection table

Tape (mm)

Weld powder

Mould code

⁦20×3⁩

⁦KWD 115⁩

⁦TT7-203⁩

⁦20×5⁩

⁦KWD 150⁩

⁦TT7-205⁩

⁦25×3⁩

⁦KWD 150⁩

⁦TT7-253⁩

⁦25×5⁩

⁦KWD 200⁩

⁦TT7-255⁩

⁦30×5⁩

⁦KWD 250⁩

⁦TT7-305⁩

⁦40×3⁩

⁦KWD 250⁩

⁦TT7-403⁩

⁦40×5⁩

⁦2 × KWD 150⁩

⁦TT7-405⁩

⁦50×5⁩

⁦2 × KWD 200⁩

⁦TT7-505⁩

⁦60×5⁩

⁦2 × KWD 250⁩

⁦TT7-605⁩

Need another size, or do your conductors not match this table? Send the conductor details or the joint drawing to our specialists and they will recommend the right mould.

KALweld® exothermic welding: copper tape to copper tape

Drag to rotate; scroll to zoom.Open full screen

Documents & Downloads

Certificates & test reports

  • Laboratory test report for KALweld® four-way conductor-to-conductor exothermic weld | Power and Water University of TechnologyPersian · 2017-03-14
  • Laboratory test report for the KALweld® conductor-to-conductor T exothermic weld | Power and Water University of TechnologyPersian

Installation & application guides

Frequently Asked Questions

What is the TT7 mould code for the smallest size?

For size 20 x 3, use mould TT7-203 with KWD 115 powder. The other sizes are in the table on this page.

How many welds can each mould make?

Our moulds are made of high-grade graphite and, used correctly and according to the instructions, last for 50 to 60 welds. Cleaning with a wire brush, knocks, moisture and opening too early all shorten mould life.

After ignition, when should the mould be opened?

Wait at least one minute for the molten metal to solidify, then open the mould carefully.

Which weld powder is right?

The powder size for each conductor size is shown in the table on this page and on the mould lid. Do not substitute powder of another size or another mould.

Have a Technical Question?

KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.