Move your pointer over the image to zoom in
Complete Product Overview
TE2 exothermic weld: through-run copper tape to the top of an earth rod
Last updated:
The TE2 exothermic weld joins a through-run copper tape to the top of an earth rod in earthing, bonding and lightning protection networks. We produce its graphite mould under our KALweld® brand and supply it with the matching weld powder and handle clamp. After welding, the joint becomes one with the conductors and has no nuts or bolts to work loose over time. KALOT's KALweld® welds have successfully passed the tests required by IEEE 837 and UL4677 in accredited laboratories, and the test results and approvals are available at the bottom of this page.
TE2 moulds are made for 14.2 and 17.2 mm earth rods and tapes from 20×3 to 50×5 mm. The mould and powder code for each size is given in the "Mould and powder selection" table, and the HC 01 handle clamp fits every size.
Technical Product Information
Click to view enlarged
Mould body material: graphite; mould lid material: stainless steel; suitable handle: HC 01.
TE2 mould and powder selection table
Earth rod diameter (mm) | Thread (inch) | Tape (mm) | Weld powder | Mould code |
|---|---|---|---|---|
14.2 | 5/8" | 20×3 | KWD 090 | TE2-142-203 |
14.2 | 5/8" | 20×5 | KWD 090 | TE2-142-205 |
14.2 | 5/8" | 25×3 | KWD 090 | TE2-142-253 |
14.2 | 5/8" | 25×5 | KWD 115 | TE2-142-255 |
14.2 | 5/8" | 30×3 | KWD 115 | TE2-142-303 |
14.2 | 5/8" | 30×5 | KWD 150 | TE2-142-305 |
14.2 | 5/8" | 40×3 | KWD 150 | TE2-142-403 |
14.2 | 5/8" | 40×5 | KWD 150 | TE2-142-405 |
14.2 | 5/8" | 50×5 | KWD 200 | TE2-142-505 |
17.2 | 3/4" | 20×3 | KWD 150 | TE2-172-203 |
17.2 | 3/4" | 20×5 | KWD 150 | TE2-172-205 |
17.2 | 3/4" | 25×3 | KWD 150 | TE2-172-253 |
17.2 | 3/4" | 25×5 | KWD 150 | TE2-172-255 |
17.2 | 3/4" | 30×3 | KWD 150 | TE2-172-303 |
17.2 | 3/4" | 30×5 | KWD 200 | TE2-172-305 |
17.2 | 3/4" | 40×3 | KWD 200 | TE2-172-403 |
17.2 | 3/4" | 40×5 | KWD 200 | TE2-172-405 |
17.2 | 3/4" | 50×5 | 2 × KWD 150 | TE2-172-505 |
The thread on the earth rod top must be cut off before welding.
These moulds are made for copper-bonded earth rods.
Need another size, or do your conductors not match this table? Send the conductor details or the joint drawing to our specialists and they will recommend the right mould.
Click to view enlarged
Preparing the conductors for tape-to-earth rod exothermic welding
Cut off the thread at the top of the earth rod before welding and flatten the end of the earth rod. These moulds are made for copper-bonded earth rods.
Steps
- Check the mould and powder against the table above; the mould code and powder size are also marked on the mould lid.
- Before the first weld, warm a cold mould with a gentle flame to drive off moisture.
- Clean the conductors to bright metal with a wire brush and dry them with a torch.
- Fit the handle on the mould, place the conductors without force in the centre of the weld chamber and lock the mould.
- Place the steel disc at the bottom of the reaction chamber with the concave side up, and gently pour the weld powder over it.
- Sprinkle starter powder over the weld powder and on the edge of the mould, close the lid and light it from the side with a flint igniter, then step away at once.
- Wait at least one minute, open the mould and inspect the weld.
- Clean the slag out of the mould with a soft bristle brush and a scraper; never clean the mould with a wire brush.
See photos of every step, safety notes and the troubleshooting table in the complete illustrated exothermic welding guide, or download the 6-page KALweld® exothermic welding instructions (PDF).
Click to view enlarged
Applications
- Connecting copper tape to the top of a copper-bonded earth rod in an earth pit
- Connecting the tape ring of an earth grid to the earth rods
- Permanent underground joint with no clamps or bolts
What does a sound weld look like?
A sound weld fills the mould chamber completely and fully covers the conductors, its slag comes away easily, and after cleaning it has a golden to copper colour. A deep cavity, unmelted conductor under the slag or an incomplete weld means the joint must be welded again.
Safety
- Wear heat-resistant gloves, safety glasses and long-sleeved clothing, and move the hot mould only by its handle.
- The mould and conductor must be dry; contact between molten metal and moisture causes spatter.
- After ignition, step back, do not breathe the fumes, and keep combustible materials away from the work area.
- Keep powder and starter in a dry place in undamaged packaging.
Conductors for this joint: copper-bonded earth rod, copper tape.
KALweld® exothermic welding: copper tape to earth rod
Documents & Downloads
Catalogues & datasheets
Certificates & test reports
- Laboratory test report for KALweld® four-way conductor-to-conductor exothermic weld | Power and Water University of TechnologyPersian · 2017-03-14
- Laboratory test report for the KALweld® conductor-to-conductor T exothermic weld | Power and Water University of TechnologyPersian
Installation & application guides
Similar & Complementary Products
Frequently Asked Questions
What is the TE2 mould code for the smallest size?
For size 14.2 / 5/8" / 20 x 3, use mould TE2-142-203 with KWD 090 powder. The other sizes are in the table on this page.
How many welds can each mould make?
Our moulds are made of high-grade graphite and, used correctly and according to the instructions, last for 50 to 60 welds. Cleaning with a wire brush, knocks, moisture and opening too early all shorten mould life.
After ignition, when should the mould be opened?
Wait at least one minute for the molten metal to solidify, then open the mould carefully.
Which weld powder is right?
The powder size for each conductor size is shown in the table on this page and on the mould lid. Do not substitute powder of another size or another mould.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.

