Move your pointer over the image to zoom in
Complete Product Overview
Stainless steel hose clamp (Hose Clamp) for lightning protection down conductors
Last updated:
KALOT's stainless steel hose clamp fixes the down conductor of a lightning protection system, that is copper tape or copper wire, to a tubular air terminal mast, a guyed mast base, a telecommunications tower or any other cylindrical object. The stainless steel band wraps around the pipe and conductor, and tightening the worm screw presses the conductor against the pipe surface with no drilling or welding. In usual practice these clamps are installed every 30 to 33 cm along the whole mast, and stainless steel offers good resistance to rust outdoors. Three models, CCS35, CCS68 and CCS11, are offered for diameters of 33 to 57, 65 to 89 and 105 to 127 mm.
We provide these clamps in three sizes, so your down conductor stays neat and lasting on any mast or tower.
A firm, neat down conductor from the top of the mast to its foot
In a lightning protection system mounted on a tubular mast, the down conductor must be fixed to the pipe along the mast's whole length. KALOT's stainless steel hose clamp does this with a stainless steel band and a worm screw: no drilling, no welding, and it can be retightened during periodic checks.
- Fixes copper tape or wire to pipes
- Stainless steel for outdoor installation and corrosion prevention
- Three sizes for diameters from 33 to 127 mm
- No drilling of the pipe or conductor
Stainless steel, made for the outdoors
The clamp stays in rain and sun for the whole life of the system. Stainless steel resists rust and, unlike an ordinary steel clamp or a damaged galvanised one, does not lose its clamping force or the neat look of the conductor run to rust.
No drilling or welding
The conductor is pressed between the band and the pipe, so neither the mast pipe nor the conductor is drilled. NF C 17-102 does not permit drilling a down conductor to fix it to its support.
For copper tape and wire
One type of clamp for both forms of down conductor: tape sits flat on the pipe and wire is held under the band.
Simple selection by diameter
Three models, CCS35, CCS68 and CCS11; the range of each model must cover the diameter of the pipe plus the conductor. For other diameters, please contact KALOT Group.
Quick installation with simple tools
The worm screw tightens with a spanner or screwdriver, and clamps that have loosened can be retightened during periodic checks.
Technical Product Information
Feature | Value |
|---|---|
Product type | Hose clamp (band clamp with worm screw) (Clamping Collar) |
Material | Stainless steel (Stainless Steel) |
Application | Fixing down conductors to tubular air terminal masts, guyed mast bases, telecommunications towers and other cylindrical objects |
Conductor type | Copper tape or copper wire |
Fixing method | Slotted band around the pipe and conductor; tightened with a worm screw |
Common installation spacing | About 30 to 33 cm along the mast (three points per metre) |
Models | CCS35, CCS68, CCS11 |
Models and clamping diameter range
Order code | Clamping diameter range (mm) | Material |
|---|---|---|
CCS35 | 33 to 57 | Stainless steel |
CCS68 | 65 to 89 | Stainless steel |
CCS11 | 105 to 127 | Stainless steel |
The outer diameter of the pipe plus the conductor thickness must fall within the range of the chosen model. For other sizes, please contact our sales department.
What role does a hose clamp play in a lightning protection system?
When an air terminal is mounted on a tubular mast, the down conductor must be fixed firmly and neatly to the pipe from the top of the mast to its foot, so that wind, vibration and the electrodynamic forces of lightning current do not shift it. A hose clamp is the simplest way to hold a conductor on a round surface: a metal band wraps around the pipe and conductor and tightens with one screw, with no need to drill the pipe or conductor and no need for welding.
The usual installation route on an air terminal mast
- Connection at the top of the mast: the down conductor connects to the air terminal or its supporting pipe (the air terminal mast) with its own dedicated connection part. The hose clamp does not replace this connection.
- Along the mast: the conductor runs down the tubular mast, usually 4 to 5 metres long, and a hose clamp fixes it to the pipe every 30 to 33 cm.
- Foot of the mast and onward route: from the foot of the mast, the conductor continues across the roof on suitable supports, such as concrete blocks on hard roofs, and down walls with wall clamps, as far as the test joint and the earthing system.
Why stainless steel?
Clamps stay outdoors for the whole life of the system, exposed to rain, sun and air pollution. An ordinary steel clamp, or a galvanised clamp with a damaged coating, rusts over time. Rust on the band or screw reduces the clamping force, stains the mast and façade, and may cause the clamp to fail completely. That is why we offer this clamp in stainless steel.
Choosing the right size
The clamp size is chosen by the outer diameter of the pipe plus the thickness of the conductor, and this figure must fall within the clamping range of the chosen model. For an air terminal mast with an outer diameter of 38.25 mm, we recommend CCS35 (33 to 57 mm). For larger pipes and masts, CCS68 and CCS11 are available. If your project's pipe diameter falls between two ranges or you need another size, please contact our sales department.
Limitations and design notes
The hose clamp is first and foremost a part that holds the conductor in place. It creates pressure contact between the conductor and the pipe, but it does not replace dedicated connection parts at points where a main electrical connection is needed, such as connecting the conductor to the air terminal, joining two conductors or connecting to the earthing system. If the mast is galvanised steel and the conductor copper, direct contact between copper and zinc in damp or corrosive environments can lead to galvanic corrosion. Review a suitable solution with the system designer, such as tinned copper tape or stainless steel tape.
Click to view enlarged
The drawing above shows the clamp's parts and the clamping diameter range of each model. D is the outer diameter of the pipe plus the conductor and must fall within the range of the chosen model.
Cross-section of the conductor-to-pipe connection
As the screw tightens, the stainless steel band presses the copper tape or wire against the pipe surface and holds the conductor in place. Position the screw housing opposite the conductor, where it can be reached for inspection and retightening.
Click to view enlarged
Where is it used?
- Tubular air terminal masts on roofs, for fixing the down conductor from the top of the mast to its foot
- Guyed mast bases and telecommunications towers with tubular members, within the clamp's diameter range
- Other cylindrical objects such as pipes and poles, wherever a conductor must be fixed along them
Installation steps
- Measure the outer diameter of the pipe plus the conductor and choose the clamp model accordingly.
- Lay the conductor straight and free of twists on the pipe, from the connection part at the top of the mast to its foot.
- Loosen the clamp screw, wrap the band around the pipe and conductor, and seat the end of the band in the screw housing.
- Position the screw housing opposite the conductor, where it will be reachable later.
- Tighten the screw until the conductor sits firmly against the pipe and cannot move; avoid overtightening that could damage the band or its slots.
- Install the next clamps about 30 to 33 cm apart, down to the foot of the mast.
Inspection and maintenance
During periodic inspections of the lightning protection system, check each clamp for tightness, rust or damage, and make sure the conductor has not moved. Retighten any clamps that have loosened and replace damaged ones.
The standards below are presented to help you understand the requirements for installing down conductors and the place of this part in the system.
ESE lightning protection systems: NF C 17-102
For fixing down conductors, this standard recommends three support points per metre (about every 33 cm). The supports must be compatible with the surface they are fixed to and allow for the conductor's thermal expansion, and drilling the conductor to fix it to its support is not permitted. The clamp spacing of 30 to 33 cm on this page is consistent with this recommendation.
System design: IEC 62305-3
This standard covers the design, installation, inspection and maintenance of a structure's lightning protection system, and requires conductors to be firmly fixed to prevent movement and mechanical damage. The system designer sets the number and spacing of supports according to the conductor type and installation location.
The catalogue datasheet (in English) is in the list below. The drawings and schematics on this page, ready to print:
Hose clamp and cable tie on a tubular pole
Frequently Asked Questions
What is a hose clamp used for in a lightning protection system?
For fixing down conductors, that is copper tape or copper wire, to tubular air terminal masts, guyed mast bases, telecommunications towers and other cylindrical objects. The stainless steel band wraps around the pipe and conductor, and tightening the screw presses the conductor against the pipe.
How far apart should the clamps be on the air terminal mast?
In KALOT Group's usual practice, one clamp is installed every 30 to 33 cm. This spacing is consistent with the NF C 17-102 recommendation of three support points per metre. On each project, the system designer sets the final spacing.
Which clamp size should I choose?
Measure the outer diameter of the pipe plus the thickness of the conductor: CCS35 for 33 to 57, CCS68 for 65 to 89 and CCS11 for 105 to 127 mm. For an air terminal mast with an outer diameter of 38.25 mm, we recommend CCS35. For diameters between these ranges, please contact us.
Why is a stainless steel clamp better than a galvanised one?
Clamps stay outdoors for years. A galvanised coating is lost once it is damaged and the clamp then rusts; rust reduces the clamping force and stains the mast and façade. Stainless steel resists rust, and the clamp holds its function better over the life of the system.
Is a hose clamp enough to connect the conductor to the air terminal?
No. The hose clamp is a part that holds the conductor along the mast. Connecting the down conductor to the air terminal or its mast, joining two conductors and connecting to the earthing system must be done with connection parts dedicated to each task.
Is this clamp also suitable for copper wire?
Yes, this clamp suits both copper tape and copper wire. In both cases, the diameter of the pipe plus the conductor must fall within the range of the chosen model.
What should I watch for if the mast is galvanised and the conductor is copper?
In damp or corrosive environments, direct contact between copper and the zinc (galvanised) coating can lead to galvanic corrosion. Review a suitable solution with the system designer, such as tinned copper tape or stainless steel tape.
Have a Technical Question?
KALOT Group's technical experts are ready to answer your questions about lightning rods and earthing systems.



